Plumbing 101: Tips for Installing a Bathtub
Plumbing 101: Tips for Installing a Bathtub
Blog Article
They are making a number of good pointers related to Installing A Bathtub as a whole in this great article underneath.
Installing a bathtub isn't exactly brain surgery, but it does require solid plumbing, woodworking, as well as occasionally, tiling skills. Replacing an old bathtub with a new one is likewise a moderately challenging task. If the old bathtub is conveniently obtainable, the task can move immediately; if you have to open a wall to get rid of the old bathtub and also position the brand-new bath tub, the task is a lot harder. In either situation, the job is within a house handyman's abilities, although you will certainly require an assistant to vacate the old tub and set in the new one. Ensure you have actually certified on your own for the job and are comfortable attempting it. As opposed to working with a professional to take control of a halfway-completed project, it is better to take into consideration using one before you start. Opportunities are you might need a specialist plumber to make tube links.
This article will certainly help you set up a brand-new bath tub in your shower room if you have actually currently purchased a new bathtub as well as do not require to alter the arrangement of your previous water supply pipes.
Your tools and material list should consist of the following:
Preparing for the Setup
Firstly, the sustaining frame provided with the bathroom ought to be fitted (if required) according to the producer's guidelines. Next off, fit the taps or mixer to the bath tub. When suitable the faucet block, it is very important to make certain that if the faucet features a plastic washing machine, it is fitted between the bath and the faucets. On a plastic bath, it is also reasonable to fit a sustaining plate under the taps unit to stop stress on the bath tub.
Fit the versatile faucet connectors to the bottom of both faucets utilizing 2 nuts and olives (often provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the outlet via the hole in the bath. Use the nut supplied by the manufacturer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bath. Ensure you make use of all of the supplied washers.
Link the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Link all-time low of the overflow tube in a similar manner.The bathroom should now be ready to be suited its final placement.
Removing Old Touches
If you need to replace old taps with new ones as a part of your installment, after that the first thing you should do is separate the water supply. After doing so, activate the taps to drain pipes any water continuing to be in the system. The process of eliminating the existing taps can be quite problematic as a result of the limited accessibility that is frequently the case.
Use a container wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipes to the faucets. Have a cloth prepared for the continuing to be water that will certainly originate from the pipes. When the supply pipelines have been eliminated, make use of the very same device to loosen the nut that holds the taps onto the bath/basin. You will need to quit the solitary faucets from turning during this procedure. When the faucets have actually been removed, the holes in the bath/basin will certainly have to be cleansed of any kind of old sealing substance.
Prior to carrying on to fit the brand-new faucets, contrast the pipe links on the old taps to the new faucets. If the old faucets are longer than the new taps, then a shank adapter is needed for the new faucets to fit.
Mounting the Bath tub
Utilizing the two wooden boards under its feet, put the bathtub in the called for placement. The wood boards are helpful in uniformly spreading out the weight of the bathtub over the area of the boards rather than concentrating all the weight onto 4 little factors.
The following goal is to make sure that the tub is leveled all round. This can be accomplished by inspecting the level and readjusting the feet on the tub till the level reads degree.
To install faucets, fit the bottom of the outermost flexible faucet port to the appropriate supply pipeline by making a compression sign up with; then do the very same for the other faucet.
Activate the water and examine all joints as well as new pipework for leakages and tighten them if necessary. Fill up the bath tub and likewise check the overflow electrical outlet and also the typical electrical outlet for leakages.
Finally, repair the bath paneling as described in the producer's user's manual. Tiling and also sealing around the tub needs to wait till the tub has actually been utilized a minimum of once as this will certainly resolve it into its last setting.
Suitable New Touches
If the tails of the brand-new faucets are plastic, then you will certainly require a plastic adapter to prevent damage to the thread. One end of the connector fits on the plastic tail of the faucet and also the various other end gives a link to the current supply pipelines.
If you need to fit a monobloc, after that you will certainly require lowering couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next off, place the faucet in the placing opening in the bath/basin making sure that the washers remain in location in between the tap as well as the sink. Protect the faucet in place with the manufacturer supplied backnut. Once the tap is safely in place, the supply pipes can be connected to the tails of the faucets. The faucets can either be connected by utilizing corrugated copper piping or with typical faucet adapters. The former kind should be attached to the faucet ends first, tightening only by hand. The supply pipelines can later be attached to the other end. Tighten up both ends with a spanner after both ends have been connected.
Tiling Around the Bathtub
In the location where the bath fulfills the ceramic tile, it is essential to secure the joins with a silicone rubber caulking. This is very important as the fitting can relocate enough to break a rigid seal, causing the water to pass through the wall surface between the bathroom as well as the tiling, leading to issues with wetness and feasible leaks to the ceiling listed below.
You can pick from a selection of coloured sealants to blend in your fixtures and installations. They are sold in tubes and also cartridges, and also are capable of securing voids approximately a size of 3mm (1/8 inch). If you have a bigger gap to fill up, you can fill it with spins of soaked paper or soft rope. Remember to always fill up the bath tub with water before sealing, to allow for the activity experienced when the tub is in usage. The sealer can crack relatively early if you do not consider this motion prior to sealing.
Additionally, ceramic coving or quadrant floor tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are likewise easily available on the marketplace. It is suggested to fit the ceramic tiles making use of water-resistant or water-proof sticky as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We were shown that editorial about How to Install a Bathtub through someone on a different site. If you appreciated our blog posting kindly do not forget to share it. Thank you for your time. Visit again soon.
Plumbing woes? Contact. Report this page